Keep dragging the hoe through the mortar in this fashion. Add the rest of the water, and continue mixing for 3 to 5 minutes. As you continue to add water and mix, the mortar will get softer and mushier. Don't worry if it doesn't look or feel right after this last bit of mixing. There is still one more step you need to do.
Let the mortar sit for 3 to 5 minutes. This will allow the aggregate to get fully soaked. Dip your trowel into the mortar, then pull it out. Flick it downward to shake off any mortar clinging to it.
If the mortar clings to it, it has the right consistency. Include your email address to get a message when this question is answered. If you need to add more water, do so sparingly. Helpful 1 Not Helpful 0. If you are mixing your Quikrete by hand, consider doing it in a wheelbarrow.
This way, you can just roll it to where you need to use it. If you have a larger job, consider mixing your cement by machine. It'll be quicker, easier, and less of a hassle. Helpful 0 Not Helpful 0. Scrub your tools, mixing contains, and wheelbarrows clean with water and a stiff-bristled brush before the cement starts to harden. Have some extra, dry concrete or mortar mix on hand.
This way, if your mixture is too wet, you can add more of the dry mix into it. Helpful 2 Not Helpful 0. If the concrete or mortar is too dry, add a little bit more water to it. Avoid adding too much water, however, or you will weaken the finished product. Submit a Tip All tip submissions are carefully reviewed before being published.
Always wear eye and skin protection. The dry mix is caustic, and it can burn your skin. If you get some cement on your skin, wash it off with water immediately. Avoid adding too much water into your concrete mix. For example, 1 extra quart 0. Related wikiHows How to. How to. More References 1. About This Article. Co-authored by:. Co-authors: Updated: September 3, Categories: Working with Concrete and Cement. Article Summary X To mix Quikrete concrete by hand, start by putting on a pair of safety goggles and some waterproof gloves.
In other languages Italiano: Miscelare il Calcestruzzo Quikrete. Thanks to all authors for creating a page that has been read 72, times. Reader Success Stories Anonymous Sep 13, Did this article help you? Cookies make wikiHow better. And even though mixing concrete is a relatively safe thing to do, there are still some precautions you can take. Make sure to wear safety glasses and rubber gloves to protect your eyes and hands from the concrete.
And be careful when lifting the bags and handling concrete. When working with cement based products, like Quikrete Concrete, always wear eye protection and waterproof gloves. I also recommend wearing a mask when you pour dry concrete into the tray, wheelbarrow or mixer because a lot of dust will kick up. And make sure to lift carefully, concrete is heavy. If your using a tub, make sure it provides enough depth and space to hold the concrete mix.
I like to get one big enough for at least 80 lb. Also, by cutting the middle you can use the edges as handles to hold the bag with. It makes pouring out the concrete a bit easier and less awkward.
If your using a wheelbarrow the advise is pretty much the same. Make sure its strong enough to carry the load. Mixed concrete can be pretty heavy. Pro Tip: Make sure you place the mixing tub or wheelbarrow near the project. Once the Quikrete bag is poured into the tub or wheelbarrow, use your hand or a tool to make an indent in the mix. An indent makes pouring in your water and mixing the concrete a little easier. Carefully measure out the amount of water you need.
Other than the concrete itself, the most important part to creating strong concrete is water. You need just enough water to get a good, thorough mix. Both too much and too little water will weaken the concrete. Follow the instructions on your bag. In most cases 3 quarts of water are required for an 80 lb. Any fresh water is typically fine to mix with concrete. Salt will weaken your concrete. The correct ratio of water to Quikrete mix is 3 quarts of water for each 80 pound bag.
Pro Tip: Measure out your water the first time and then pour it into a 5 gallon bucket. Make a mark that will act as your fill line. This is a fast and easy way to always get the water right. For each 80 lb.
Pour water into the depression you made earlier. Mix the water and dry concrete together until your water is completely soaked up. Work the mix with a tool, gradually adding water, until the mix reaches a uniform consistency. Properly mixed concrete will look like thick oatmeal and hold its shape. You should be able to form concrete in your hand like a snow ball. If the concrete is like soup then add more dry mix to balance it out.
If the concrete is too dry with unmixed concrete, add some water. Do Not use more water than is required.
Excess water weakens concrete. It makes concrete brittle and prone to cracking. On a windy day, do this step indoors, perhaps in the garage, to avoid making a mess.
Having filled up your watering can in preparation for the project, pour a little of the liquid into the center of the mounded concrete mix. Worried about using too much or too little? Allay your uncertainty by employing a kitchen measuring cup to fill the watering can with a carefully pre-measured volume of water. Combine the concrete and water, working the material in a back-and-forth motion, using either a shovel or garden hoe. The goal here is to evenly distribute the water across the powder.
First, cut the bottom off a plastic or paper cup. Next, shape the container into a cone. Scoop up enough concrete to fill the cone, then empty the cone onto a flat surface.
0コメント